Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS

$34.95 Buy It Now or Best Offer
free,30-Day Returns

Seller Store method2kh
(6500) 100.0%,

Location: Central Islip, New York
Ships to: US,
Item: 165377903570

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Generic:Generic
Type:Complete XENO Kit
Compatible Model:Nintendo GameCube
Compatible Product:Controller

Product Details:This is a listing for complete mod kit for your GameCube. Each kit contains the following:SWISS (Latest copy) Boot Disc on vintage 2005 media w/ frosted Case and front cover artwork (no disc artwork) XENO ModchipSD2SP2 Adapter (Random color unless specified) (If you require a GECKO instead please let me know, you can choose either the GECKO or the SD2SP2. SD2SP2 will be given by default.) CR2032 Battery Holder CR2032 Battery4.5mm Gamebit screwdriver bit LED Controller Port Mod KitLED Controller Port Mod Kit:Each LED controller Port Mod Kit contains the following:5x 470 ohm Resistors (4x are required for the install, 1x is a spare just in case)5x LEDs of your choice (4x are for the controller ports, 1x is for main LED)20 inches of red 26 AWG wire (you will have a surplus of wire, just in case) 20 inches of black 26 AWG wire (you will have a surplus of wire, just in case)4x Red shrink tube4x Black shrink tubeLED:I have the following colors in stock: Red/Orange/Yellow/Green/Blue/White/Pink/Purple(UV)/Chartreuse/Warm-white/slow-cycling RGB (please message me your choice or write it in a message during checkout)These are 5mm and look fantastic in the GameCube. The original LED size is 3mm, so these are brighter. I did notice that the UV one is somewhat dim. RGB LEDs do not sync across and is not suggested as a selection.The orientation matters. The longer leg is called the anode, the shorter leg is the cathode.Please look at the photo in the ad to check out the orientation or take a photo of your board beforehand.You have to bend the legs of the main LED. Put the LED completely in the hole, then bend the legs. Secure it with kapton/electrical tape, then solder the LED into place.XENO Install Notes:This is to be considered a 4/10 difficulty. Refer to picture #5 for how the install should look like. The XENO chip should be surface mounted, this is much quicker and has less room for error.You must pre-tin the PCB board, there are three main points that need to be pre-tinned, they are copper pads. Solder will not want to flow directly onto the copper pads, place the soldering iron on the copper pad for a few seconds, then add solder; it should now flow directly onto the pad. After pre-tinning, use copper braid to remove all solder on those three main points and clean gently with alcohol. Place the XENO into place, secure it with Kaptop tape (or electrical tape), and then solder all the necessary points.Flux is not necessary if you work quickly, but flux is HIGHLY recommended and will make the soldering job much easier. The actual soldering job should be done in less than 60 seconds.The hardest point to solder is the top middle point (next to a 6 marking), solder must only go on one of the copper pads (the pad to the right).You will know if the XENO install was successful if it boots to a solid red LED, flickers, then goes solid orange. If there is no LED light, the top left solder point on the XENO chip is soldered incorrectly. If the red LED flickers constantly, check your solder points.LED Controller Port Mod Install Notes:This is to be considered a 7/10 difficulty. Set aside 45 minutes for a complete install.Please start by looking over in complete detail the video located here: https://www.youtube.com/watch?v=jq2mFzSMzr4 The video listed above is by no means perfect and can absolutely be improved upon. Read some of the notes below. Start with bending the controller port notches, this is where you will be placing the LED into after the whole soldering job is done. (You want to do this first, as you can mess up your soldering work if you do this last). Do not bend the notches too much, you want them to grab the LED tightly. Hot glue is not necessary if you use this notch technique.Prep all the wires, shrink tube, resistors, and LED FIRST. Once you create four units, THEN solder them onto the PCB board. The color of the wire does not matter, I always keep the red tubing with the red wire just for consistency.Each four units that you create must not be too long, nor too short; if it is too short it will not reach into the notch, if it is too long you will not be able to close the top lid. You will have to bend each unit to be placed into the controller port notch that you created. This may seem very intimidating after you have soldered everything, but this is necessary; if you do not bend the resistor into the notch then the case will not close.The heat shrink tubing is optional but highly recommended so you do not short anything inside the case.Test the board before closing the top of the case. I like to test the board even before putting the LEDs into the controller port notchPhoto #6 is a good example of the finished job before putting the LEDs into the controller notch, although should have the black shrink tubing.This install is really about technique and doesn’t have to be extremely clean if this is your first time. Just make sure that before you close the top lid check the orientation of the LEDs so they all shine down evenly. It will take a lot of patience but I assure you it will be one of the most gratifying installs you will do to your GameCube!Misc Notes:When you put back the top of the case, YOU MUST keep the disc tray open or else you WILL destroy the legs of the eject mechanism that is attached to the DVD drive. This is why that board is so expensive, it is not repairable if those two small legs are destroyed, and the only reason why those legs break is because the technician did not keep the disc tray open when putting back the top of the case!Be very careful when removing the ribbon cable on the PCB board, ESPECIALLY when putting it back into the GameCube motherboard. There are these silver pins on the ribbon that you can fray and destroy if you insert this ribbon incorrectly! When inserting it back in, notice a small crease on the end of the ribbon, bend that to a 90 degree angle, then put your finger on top of the bend, position the ribbon, and press down gently. This is really about technique, so take your time.When putting back the 4.5mm screws DO NOT re-thread the screws! What this means is that if the screw does not easily go in, you must remove it and try again. You can snap the legs inside the GameCube case if you rethread the screws. Hint! Go counterclockwise when screwing in screws until you feel a slight CLICK. Once you feel that click, screw clockwise, the screw should be in position.If you find a mistake on this ad, or think I should add any special pointers to help others, please message me.I understand the amount of literature on this ad is overwhelming, please read it over carefully, it is only meant to help you.This is for a kit, not a completed pre-soldered controller board.I do not offer pre-soldered controller boards, there is too much room for error when mounting/positioning the board. Shipping: Location Service 1st Item Additional USA USPS Ground Advantage Free Free USA USPS Priority $7 Free USA USPS Express $25 Free Insurance:Insurance is included on all purchases, protecting against loss or damage during transit. If you would like signature confirmation, it is an additional $2.65. If your package is stolen once delivered, USPS nor myself are responsible. If the order has a total cost (including shipping costs and any taxes) of $750 or more, the seller is required to purchase signature confirmation.Please contact me prior to your purchase if you are interested in this service. Return Policy:All items are guaranteed against D.O.A. (dead/defective on arrival). If by chance your item is non-functional upon arriving, or not as described in the ad, a refund will be given up to 30 days of ad closing.Refunds will only be granted based upon this criteria. Buyer must pay for return shipment, and actual shipping costs will be deducted from the refund as well. Item must be returned in original condition complete with all material. International Buyers:Please note that customs duties and taxes are solely the responsibility of the buyer. In addition, the time frame in which an international package takes to arrive might fluctuate based on it’s clearance through customs. The USPS, eBay, or myself have no control over this aspect and will not be held responsible. For any further inquiries, feel more than free to contact me 24/7!!!Thanks for looking & have a great day!!

Frequently Asked Questions About Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS in My Website

graphiste-marionbinetruy.com is the best online shopping platform where you can buy Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS from renowned brand(s). graphiste-marionbinetruy.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS on graphiste-marionbinetruy.com?

Frequently Asked Questions About Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS in My Website

What are the best-selling Nintendo GameCube Complete XENO Kit w/ LED Controller Port Mod, SD2SP2, SWISS on graphiste-marionbinetruy.com?

Laisser un commentaire